厭氧發酵產生的沼氣內含有一定的硫化氫，硫化氫不但會腐蝕管道及設備，更嚴重的是如果接觸到人員，會造成硫化氫中毒，給人們的身體健康造成危害，嚴重時可以致人死亡。沼氣脫硫的方法有很多，堿液脫硫法是常用的方法之一。該工藝以Na2CO3(NaOH)水溶液為吸收劑，擇優選擇催化劑，自吸空氣噴射氧化槽再生，壓濾脫硫泡沫等工藝過程，達到全過程無污染的設計目標。

　　The biogas produced by anaerobic fermentation contains a certain amount of hydrogen sulfide. Hydrogen sulfide not only corrodes pipelines and equipment, but more seriously, if it comes into contact with personnel, it can cause hydrogen sulfide poisoning, posing a threat to people's health and even causing death in severe cases. There are many methods for biogas desulfurization, and alkaline desulfurization is one of the commonly used methods. In this process, Na2CO3 (NaOH) aqueous solution is used as absorbent, catalyst is selected preferentially, regeneration of self-priming air jet oxidation tank, pressure filtration desulfurization foam and other processes are used, so as to achieve the design goal of pollution-free in the whole process.

　　脫硫過程化學反應分為兩步，以NaOH堿源為例，反應過程如下所示：第一步：吸收沼氣中的H2SH2S+NaOH=NaHS+H2S第二步：催化劑的催化氧化作用下析出單質硫             NaHS+O2=NaOH+2S

　　The chemical reaction in the desulfurization process is divided into two steps. Taking NaOH alkali source as an example, the reaction process is as follows: Step 1: Absorption of H2SH2S+NaOH=NaHS+H2S from biogas Step 2: Under the catalytic oxidation of the catalyst, elemental sulfur is precipitated NaHS+O2=NaOH+2S

　　1、脫硫工藝描述發酵罐產生的沼氣進入濕法脫硫復合塔底部，自下而上流動，與上部噴淋下的脫硫液逆流充分接觸，沼氣中的H2S被吸收，凈化后的沼氣出界區進入下道工序。吸收了H2S的堿液經過催化氧化再生后循環使用，再生得到的硫泡沫經脫硫?qū)Ｓ脡簽V處理制成硫塊出售。脫硫液返回系統使用。

　　1. The desulfurization process describes that the biogas produced by the fermentation tank enters the bottom of the wet desulfurization composite tower, flows from bottom to top, and fully contacts with the desulfurization solution sprayed from the upper part in reverse flow. The H2S in the biogas is absorbed, and the purified biogas leaves the boundary area and enters the next process. The alkali liquor absorbed H2S is recycled after catalytic oxidation regeneration, and the regenerated sulfur foam is made into sulfur blocks for sale after desulfurization special filter pressing treatment. The desulfurization solution is returned to the system for use.

　　2、脫硫液流程從脫硫塔底部引出的富液(吸收H2S，生成NaHS)首先進入富液槽，再經再生泵加壓至后送至再生槽噴射器。富液高速通過噴射器噴嘴時，噴射器吸氣室形成負壓自動吸入空氣，富液與空氣兩相并流經噴射器喉管、擴散管由尾管排出并由再生槽底部并流向上流動(第二步反應)。此時，富液中的懸浮硫顆粒被空氣浮選形成泡沫飄浮在再生槽上部，溢流至硫泡沫槽內。清液與泡沫分離后經液位調節閥進入塔底經脫硫泵加壓，進入塔頂，經過吸收硫化氫后的貧液轉化成富液并流入塔底，最后進入富液槽，如此循環。再生槽上部分離出的硫泡沫流入泡沫槽、經泡沫泵送入壓濾機，從而得到純度較高的單質硫。其中產生的清液經降溫、活化、沉淀后返回溶液系統。系統工藝用水、純堿、催化劑的補充在加藥槽中完成，每天定期取樣檢測脫硫液內純堿、催化劑的濃度，并根據結果確定添加量

　　2. The rich solution (absorbing H2S and generating NaHS) extracted from the bottom of the desulfurization tower in the desulfurization process first enters the rich solution tank, and then is pressurized by the regeneration pump and sent to the regeneration tank injector. When the rich liquid passes through the nozzle of the injector at high speed, negative pressure is formed in the suction chamber of the injector to automatically suck in air. The rich liquid and air flow through the throat and diffusion tube of the injector, and are discharged from the tail pipe and flow upward from the bottom of the regeneration tank (second step reaction). At this time, the suspended sulfur particles in the rich solution are floated by air flotation to form foam and float on the upper part of the regeneration tank, overflowing into the sulfur foam tank. The clear liquid separated from foam enters the tower bottom through the liquid level control valve, is pressurized by the desulfurization pump, and enters the tower top. After absorbing hydrogen sulfide, the lean liquid is converted into rich liquid and flows into the tower bottom, and finally enters the rich liquid tank for circulation. The sulfur foam separated from the regeneration tank flows into the foam tank and is pumped into the filter press by the foam pump to obtain the elemental sulfur with high purity. The resulting clear liquid is cooled, activated, and precipitated before returning to the solution system. The replenishment of system process water, soda ash, and catalyst is completed in the dosing tank. The concentration of soda ash and catalyst in the desulfurization solution is sampled and tested regularly every day, and the amount of addition is determined based on the results

　　本文由 沼氣脫硫   友情奉獻.更多有關的知識請點擊   http://m.sylsgd.com/ 真誠的態度.為您提供為全面的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.

　　This article is contributed by the friendship of biogas desulfurization. For more related knowledge, please click http://m.sylsgd.com/ Sincere attitude. We provide you with comprehensive services. We will gradually contribute more relevant knowledge to everyone. Please stay tuned